Is DCF Overrated? Pros and Cons of Everyone’s Favorite UL Fabric

DCF was the revolutionary backpacking fabric of the 2000s. Borrowing an innovative fabric from sailboat racing, hikers were suddenly able to cut their tent weight by 50 percent overnight. At a time when 20-plus-pound base weights had been common, 15- and even 10-pound base weights suddenly became widely attainable. DCF (Dyneema Composite Fabric) has since grown in popularity. It’s now used for all sorts of backpacking applications, from packs to rain jackets.

Gear makers were quick to tout it as a do-anything, no-compromise fabric. It’s 15x stronger pound-for-pound than steel, it’s totally waterproof, it will make your tent 40 percent lighter.

What the marketing teams didn’t mention were the fabric’s downsides. You’ll pay twice as much, an aggressive pine needle can puncture it, your neighbor can see your butt’s outline through it.

After a decade of popularity, is this miracle material all it was cracked up to be?

SMD Deschutes Plus (Silnylon). By morning, it was wet with condensation and sagged enough to hit this hiker in the face for an early morning wake-up call, a common complaint of nylon.

DCF ≠ Dyneema

There are a lot of misnomers in the land of tech fabrics. To clarify a few terms:

Dyneema: A brand-name version of UHMWPE (Ultra High Molecular Weight Polyethylene). It is a fiber, not a fabric. Formerly known as Cuben Fiber.

DCF: Dyneema Composite Fabric, or a textile made of a widely spaced grid of Dyneema fiber sandwiched between two sheets of polyester plastic laminate (mylar). Often used for tarps/tent flys and stuff sacks.

DCH: Dyneema Composite Hybrid. A textile made of DCF with an additional face fabric to protect it from abrasion (typically 50D or 150D polyester woven fabric). Typically used in packs.

Ultra: A new fabric by Challenge Outdoor. A woven fabric with a 70-percent UHMWPE, 30-percent polyester face and a plastic laminate backing, similar to DCF. Typically used in packs.

Silnylon: Short for silicone-coated nylon, the most common fabric for tents and stuff sacks. This fabric is woven and coated, not laminated.

SilPoly: Short for silicone-coated polyester; similar to silnylon but not used as often. This fabric is becoming more popular because it  costs about the same as silnylon but doesn’t absorb as much water or stretch when wet.


What Makes DCF So Good?

High Tensile Strength: Due to the high strength-to-weight ratio of Dyneema, a very small amount of the fiber is strong enough for tension applications, such as pyramid tents and cordage.

Climbing slings made with 100 percent Nylon (left) vs. 100 percent Dyneema (right), both rated to 22kn (~5000lbs). The nylon version weighs 48% more.

Very Waterproof*: In lab tests, DCF is very waterproof. Some tests have rated it to over 10,000mm of hydrostatic head. In other words, a 32-foot-tall column of water could sit on top of it before it leaks. This is largely thanks to it being a laminate, where two solid layers are supported in the middle by the tension strength of Dyneema. Woven and coated fabrics like silpoly are more likely to have a lower score because the threads can start to separate more easily.

*These are lab tests on brand-new fabric. See the next section for more detail.

Light as a Feather: Ultralight gear makers typically use one of three common weights for DCF: 0.34, 0.51, and 1.0 oz/yd². For comparison, nylon and poly fabrics often start at 1.0 oz/yd² and quickly move closer to 2. Functionally, products made with DCF enjoy a 25 to 50 percent gross weight reduction compared to nylon and polyester.

For example, Tarptent uses 1.5 oz/yd² nylon for their standard Notch tent. In contrast, the ultralight Notch Li uses .55 oz/yd² DCF for the fly and 1.0 oz/yd² DCF for the floor. The standard model weighs 27.6 ounces (without stakes) compared to 20.4 ounces for the DCF “lithium” version—a 26 percent weight savings.

Low Stretch/Sag: Dyneema has very low elasticity and does not stretch when it absorbs water (which it has little capacity for anyway). This means once you pitch a tent made with Dyneema fibers, it will retain its shape and tension unless your stakes pull out.

Does Not Gain Weight When Wet: Because the fabric has very little absorbency, it’s easy to shake out and won’t feel waterlogged after an overnight deluge, a common complaint with silnylon.

Easy To Repair: Because there is a smooth plastic layer on both faces of DCF, repair tape will produce a permanent, full-strength, waterproof repair as long as the patch is appropriately sized.

Both my tent doors and trekking pole cups had significant damage by the end of the CDT, about 160 nights of use by this point. These tape repairs are permanent but add weight—and I didn’t get every pinhole.

What Are the Drawbacks of DCF?

Very Poor Abrasion and Puncture Resistance: While Dyneema itself is a reasonably cut-resistant fiber, the laminate layer that makes DCF repel water and retain its shape is very weak.

A single slide against rough surfaces like rocks can put dozens of microscopic holes in DCF. Stuff sacks can get pinholes just from contact with normal gear inside your pack like charger cables, battery banks, and sunscreen tubes. Some theorize that damage from packing DCF tents in tight stuff sacks causes more leaks than environmental factors do.

Site selection is crucial to keep DCF tent floors in good shape. Gravel, rock, sharp pine needles, goatheads, and cactus needles can all puncture them with ease.

Waterproofness Fades Quickly: While a brand-new sheet of DCF may be able to hold back a tsunami, it doesn’t take much wear and tear for small holes to create leakage. This is especially common on tent floors and around “rigid” sections (line locks, trekking pole cups, three-way corners, etc).

Longevity: Pinhole leakage, delamination, etc. mean DCF tents often last just half as long as silnylon and silpoly tents. Most manufacturers and hikers say a DCF tent will last “one full thru-hike” of a Triple Crown trail (approximately 150 nights). Their conventional counterparts are much more likely to last 300 to 400 days.

Cost: Name-brand DCF is expensive. Due to the difficulty of sourcing and laminating an appropriate mylar layer, no other manufacturer has managed to make something as light and strong to create cost competition. For example, the silpoly Tarptent Protrail costs $239, while the DCF version costs $529. That’s a 221 percent markup for a tent estimated to last half as long. If you break that out into the cost of using your tent per night, it may be four to five times more expensive to go light.

Packed Volume: DCF becomes very bulky when packed, especially fabric weights at and above 0.5 oz/yd². Despite weighing 25 to 50 percent less than their silnylon counterparts, the UL versions of most tents are the same volume or even larger, meaning a bigger backpack.

DD X-Mid 1 Solid (winter) vs. 1 Pro. Despite the Pro being single-wall and lacking some of the Solid’s burlier winter features, the two tents pack to similar sizes due to the Pro’s DCF fly.

Difficulty to Manufacture: Despite the obvious appeal of big weight savings, it has taken a surprisingly long time for DCF tents to become reliable and consistently made. DCF and especially DCH can delaminate, meaning the layers of the fabric “unglue” from each other.

Makers have extensively tested and debated the best way to join and seal DCF and DCH edges. What size needle is best? What type of thread? Do you sew at all or just use tape? Tape the inside or outside? Is hot bonding worth the cost? What factory has the expertise to work with this niche material?

Several cottage brands tested and then abandoned DCF tents for this very reason in the early days. There is better consensus now on how to work with this material, but it’s not as safe and straightforward as classic woven materials.

Shrinkage: If your superlight stuff sack or tent feels a little snugger than when it was new, it’s not your imagination. As the fabric is used, packed, and scrunched up, it can shrink. Dan Timmerman at Timmermade theorizes this is due to the mylar “bunching up” around the Dyneema fiber. While shrinkage seems to be reversible, it would be difficult and time-consuming to do on an ongoing basis.

Personally, I have used many DCF stuff sacks and had to replace several over the years due to leakage. When I got an “identical” replacement, the size difference shocked me. Over time, my old stuff sacks had experienced between 5- and 15-percent linear dimension loss. Even 10 percent shrinkage in any direction equates to a 27 percent loss in volume. That’s enough to make your sleeping bag not fit anymore.

Translucency: The weave of Dyneema fiber is widely spaced and the laminate is not particularly opaque. As a result, DCF tents are relatively see-through. If you get a strong backlight at sunset while setting up, your neighbor might get a higher-detail silhouette of your butt than you would hope for. This is particularly bad with the superlight 0.34 oz/yd² versions used by some manufacturers.

Tarptent Notch Li in Iceland. Notice how the inner tent and sleeping bag are visible, as are the hot-bonded seams on each panel.

Winter Performance: DCF and DCH both tend to become rigid and crinkly when the temps dip below freezing. Freezing rain, slush, and freezing body vapors stick to the fabric aggressively. And ice can’t always be removed safely without thawing first. Silpoly has remained popular for winter and alpine products for this reason.

Is a DCF tent worth it?

Despite its many drawbacks, UHMWPE-based backpacking products remain popular for their ability to slash weight. The main downsides (abrasion resistance, cost, and manufacturing techniques) have all improved as experience and competition have grown. Whether spending $300 to save 10 ounces is worthwhile will vary with your use, budget, and experience level.

Personally, three of the five tents I currently have are DCF, both of my high-volume packs are made of Ultra (a DCH competitor), and I use a single DCF stuff sack for odds and ends. However, I wouldn’t recommend the same to a budget-conscious or new backpacker.

You can get more bang for your buck with DCF by taking good care of it. Roll (don’t fold/stuff) your tent, pick campsites carefully, and use an oversized tent stuff sack to avoid cramming it in on a rushed morning.

Featured image: Photo via GPS. Graphic design by Zack Goldmann.

Affiliate Disclosure

This website contains affiliate links, which means The Trek may receive a percentage of any product or service you purchase using the links in the articles or advertisements. The buyer pays the same price as they would otherwise, and your purchase helps to support The Trek's ongoing goal to serve you quality backpacking advice and information. Thanks for your support!

To learn more, please visit the About This Site page.

Comments 13

  • Pinball : Mar 2nd

    Awesome informative and timely for me. I’ve happily used copper spur UL2 historically but taken the plunge on a zpacks duplex dcf on a Black Friday sale. Now I know just how much to respect campsite selection, clearing and breakdown, repack.

  • Jason McGrath : Mar 3rd

    Well done! Great info for the masses; especially those new to going light.

  • Mark Ferwerda : Mar 3rd

    To summarize:
    – 2x the cost of a similar shelter in silpoy/silnlyon
    – 1/2 the life silpoly/silnylon due to abrasion resistance
    – packs larger
    – shrinks over it’s lifespan (does it pack smaller then?)
    – weighs less (conversely you can get a larger tent for the same weight, but then there’s the size thing)
    – absorbs less water weight (so it weighs even less after a night or rain)

    It seems weight is the overriding priority/advantage here. And I get it. I’ve looked seriously at DCF tent. But I could never see how 1 pro over-rides all the cons. But that is just me.

    Nice rundown of the qualities of DCF!

  • Frank : Mar 3rd

    One important thing missed in DCF tents is the very common failure of zippers. When a tent is made of a material that has no give but is joined by a weaker link like a zipper, it will be the zipper that has to absorb all that force when the winds bear down. At some point and as evidenced in a myriad of youtubers and blogger videos the ultralight zipper is going to bust.

  • Jacko : Mar 4th

    You missed the con that makes me avoid it.
    It’s fugly

  • Ryan K : Mar 5th

    Thanks for the great article. I feel like the cons are mostly ignored in the UL community and the recommendations are always to go DCF if you can afford it. And this is actually the first time I’ve read about the halved longevity. Was that specifically with regard to tents? Have DCF packs also had reduced longevity? Or tarps? Especially hammock tarps where abrasion is rare, no zippers, etc.

    • GPS : Mar 6th

      DCF will have the same failure modes regardless of application: tents, tarps, stuffsacks, etc. basically if it is making frequent or rough contact with anything or being forced into an overly tight stuff sack, it is going to get pinholed. Tarps don’t really get a pass since they can still make contact with branches, have things fall on them (branches, pinecones, hail), and get packed into a stuffsack or your bag.
      Packs are a little different, since they almost always use DCH which has a face fabric of woven polyester. The mylar backing (inside face) can still get pinholed and leak but this usually doesnt cause all out failure. Usually DCH fails due to delamination, where the polyester face detaches from the DCF layer. Also the most commonly used versions of DCH have 50D or 150D faces, which isn’t very much. There’s a reason Ultra, which comes in 100D, 200D, 400D, and 800D, has quickly been picked up by the cottage industry. Its simply better suited to be a pack material than gluing another layer to make up for DCFs shortfalls.

  • Galen : Mar 6th

    I have an a few DCF tents, pods and a Hybrid pack while I’ve seen the ultra light gran shaving become and obsession, I see the same people packing jet boilers, excessive food, camp shoes, tons of tech gear, and while you may have 10lb base weight, most people loose the weight savings with over packing, I’ve been guilty of this, something about weighing out at 10 makes you feel like you can throw extras in, eod you adjust to you pack weight after about 3 days, I honestly feel like weight distribution is the biggest factor in a comfy long haul.

    My advice would be if this is something you love and it’s going to make you excited to get up in the mountains that’s where the value is. – On the other hand it’s not game changing, you might want to put that extra money into high quality UL down or tech-layers or shoes.

    One thing to consider is most DCF tents mount with poles, and lots of guylines like 8 or even 12, that’s a lot of stakes and as an off trail hiker and climber I really have to select a large spot that can accommodate either that much soil or collect rocks, sometimes after a 8 hour day the last thing you want to do is search for a suitable spot and hope it works for a decent pitch.

    • GPS : Mar 6th

      I agree that tents with lots of stakes are annoying, although this is more of a trekking pole/pyramid vs freestanding dome issue than material. overall footprint is also reduced when you can have a dome so everything is not constructed with straight lines. Having 4 required stakes was definitely a factor when I picked the TT Notch and Dan Durston tents vs something like an altaplex or other zpacks tent that are usually 6-10 required.

  • PJB : Mar 6th

    I’ve had a few DCF hammock tarps fail due to pinholes and wetting through. I fold & roll & pack them loosely in their stuff sacks. I noticed with my last one that the mist of sap from conifers caused the tarp sides to stick together when rolled/unrolled. I think this may be contributing to their demise. Unfortunately I’m addicted to them and recently purchased a new one. I think we need an abrasion proof and sticky proof outer layer on the fabric.


What Do You Think?